-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)
-
1S 2A BMS Board 3.7V 18650 Lithium Battery Protection Board
Features:
- Easy to use
- Color: Green
- The internal resistance difference is not more than 5mQ
- BMS Li-ion Battery Protection Board
- The tolerance is less than 30mAh
- Single-cell consumption of battery (self-consumption): ≤3uA
- In this MOSFET are employed to do the monitoring task which protects our battery cells from overcharge
Precautions:1. Before installing the protection board, the battery should be matched well (the voltage difference between each battery should not be 0.05V, the internal resistance difference is not more than 5mQ, the tolerance is less than 30mAh), the smaller the battery voltage difference, the better the protection board will work. .2. The batteries are connected in parallel and then connected in series, and the welding is correct (18650 battery nickel spot welding, other batteries are soldered), do not screw, easy to burn the protection board IC.3. If it is an old battery change board, please pay attention: Please confirm the battery is normal before buying?4. When installing, use a multimeter to check whether the voltage of each string is the same. The performance failures with a difference of more than 1.0V are: running not far, starting and powering off, charging time is short, basically the battery core problem is more. The failure of the protection board is as follows: the battery cannot be charged, and the battery has a voltage and cannot be discharged.₹15.00 (excl. GST)1S 2A BMS Board 3.7V 18650 Lithium Battery Protection Board
₹15.00 (excl. GST) -
1S 3.7V 3A 2MOS BMS Li-ion 18650 Battery Protection Board
1S 3.7V 3A 2MOS
Features:
- Small size designed for a four-cell battery pack.
- Simple and convenient circuit for easy connections
- Over-charge/Over-discharge Protection.
- Pre-soldered Nickel Strip ready to mount on battery.
₹26.00 (excl. GST)1S 3.7V 3A 2MOS BMS Li-ion 18650 Battery Protection Board
₹26.00 (excl. GST) -
1uF (1000nF) 50V Capacitor 1206 SMD Package – (pack of 5)
Features:
- Supplied in tape on reel
- Nickel-barrier end termination
- RoHS compliant
- Halogen Free compliant
₹5.00 (excl. GST)1uF (1000nF) 50V Capacitor 1206 SMD Package – (pack of 5)
₹5.00 (excl. GST) -
1X40 Right Angle Female Header Berg Strip
- Connector: Pin Header
- Connector type: Pin Strips female
- Number of pins: 40
- Pin Length: 12mm.
- Pitch: 2.54mm.
₹6.00₹7.00(excl. GST)1X40 Right Angle Female Header Berg Strip
₹6.00₹7.00(excl. GST) -
2 Channel 12V Relay Module with Optocoupler
- Low Level Trigger Relay Module
- Two separate LEDs for On/Off indication of the Relay.
- Triggering input voltage 3.3V – 5V
- Two separate LEDs for On/Off indication of the Relay
- Triggering input voltage 3.3V – 5V 4)
- Back EMF protection
- Back EMF protection 2 LEDs to indicate when relays are ON.
- Works with logic level signals from 3.3V or 5V devices
- Opto isolation circuitry
- Module with diode current protection, short response time
- AC Control Voltage: 250V @max.10A
- DC Control Voltage: 30V @max. 10A
₹65.00 (excl. GST)2 Channel 12V Relay Module with Optocoupler
₹65.00 (excl. GST) -
2 Channel 5V Relay Module
- The module using Songle relay control.
- AC voltage 250V, AC current 10A, maximum DC voltage 30V DC current maximum 10A.
- Power indicator (green), Two ways of relay status indicator light (red).
- Using 8550 transistor-driven, strong driving ability.
- Has the fixed bolt hole and easy installation.
₹55.00 (excl. GST)2 Channel 5V Relay Module
₹55.00 (excl. GST) -
2 Channel 5V Relay Module with Optocoupler
- Low Level Trigger Relay Module
- Two separate LEDs for On/Off indication of the Relay.
- Triggering input voltage 3.3V – 5V
- Two separate LEDs for On/Off indication of the Relay
- Triggering input voltage 3.3V – 5V 4)
- Back EMF protection
- Back EMF protection 2 LEDs to indicate when relays are ON.
- Works with logic level signals from 3.3V or 5V devices
- Opto isolation circuitry
- Module with diode current protection, short response time
- AC Control Voltage: 250V @max.10A
- DC Control Voltage: 30V @max. 10A
₹65.00 (excl. GST)2 Channel 5V Relay Module with Optocoupler
₹65.00 (excl. GST) -
2 Channel Logic Level Converter 3.3V 5V TTL
- Material: Plastic + metal
- Portable, small, easy to use.
- Comes with 2 rows of 6pin, unsoldered.
- The compatible breadboard can be directly inserted into the breadboard.
₹37.00 (excl. GST)2 Channel Logic Level Converter 3.3V 5V TTL
₹37.00 (excl. GST) -
2 Pin JST XH 2.54mm Pitch Plug and Socket with Cable – 10 Pcs.
2 Pin JST XH 2.54mm Pitch
Operating Temperature (°C): -25-85
Flammability Rating: UL94V-0
Cable Length(cm): 30
Allowed Wire Size: 30-26
₹58.00 (excl. GST)2 Pin JST XH 2.54mm Pitch Plug and Socket with Cable – 10 Pcs.
₹58.00 (excl. GST) -
2 Pin Tactile Micro Switch
- High precision mechanism design offers acute operation and long service life.
- Used in the fields of electronic products, household appliances and more.
- Feature momentary contact, 2 pins, round black push button, through hole mounting
- Size: 6 x 6 x 5mm. 2 Pin
₹1.50 (excl. GST)2 Pin Tactile Micro Switch
₹1.50 (excl. GST) -
2.2K Ohm Carbon Film Resistor-pack of 50 pcs
- Resistance Value: 2.2 Ohms
- Rated Power: 0.25 Watt (1/4W); Tolerance : +/- 5%
- Carbon Film Resistor – Through Hole; Flame Retardant Coating
- Stiff 24 gauge leads (0.022 inches, 0.55 mm) perfect for solderless plug-in breadboards
- Package Include 10 x 2.2 Ohm (Note: Color of resistor may change, so please contact us if you need specific color resistors)
₹50.00 (excl. GST)2.2K Ohm Carbon Film Resistor-pack of 50 pcs
₹50.00 (excl. GST) -
2.4″ Inch Touch Screen TFT Display Shield
- 2.4″ Touch LCD TFT display module for Arduino
- 240*320 pixels resolution
- Ability to display 262000 different colors
- The shield comes equipped with a microSD card slot.
- SPFD5408 controller with built-in video RAM buffer
₹500.00 (excl. GST)2.4″ Inch Touch Screen TFT Display Shield
₹500.00 (excl. GST)
