-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)
-
1 Channel Relay Module, 30A with Optocoupler, Isolation 12V Supports, High and Low Triger
- Channel: 1 channel
- Relay Voltage: 12V
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
₹122.00 (excl. GST) -
10mm Spiral Wrapping Band Black 10M for Wires
Features :
- Extremely versatile in flexibility
- Designed to Hold and Protect Cables, Harnesses, and Hoses
- Allows Flexibility while Providing Secure Bundling
- Quick and Easy to Install due to Flexible Polyethylene Construction
- Easily removed and re-applied
- Thick wall Provides Greater Resistance to Abrasions and Vibrations
- Breakout at Any Point
₹120.27 (excl. GST)10mm Spiral Wrapping Band Black 10M for Wires
₹120.27 (excl. GST) -
74HC4075N LOGIC GATE IC
74HC4075N
Logic Gates TRIPLE 3-INPUT OR GATE₹120.00 (excl. GST)74HC4075N LOGIC GATE IC
₹120.00 (excl. GST) -
SN74LS136N GATE IC
SN74LS136N
XOR (Exclusive OR) IC 4 Channel Open Collector 14-PDIP
₹120.00 (excl. GST)SN74LS136N GATE IC
₹120.00 (excl. GST) -
Aluminum Flexible Shaft Coupling 5mm x 5mm
Features :
- Corrosion resistance and High Durability
- One piece construction with long-lasting performance
- Torsional stiffness: Zero backlash
- Low moment of inertia offering constant velocity
₹120.00 (excl. GST)Aluminum Flexible Shaft Coupling 5mm x 5mm
₹120.00 (excl. GST) -
GY-271 HMC5883L 3-axis Electronic Compass Module
GY-271 HMC5883L 3-axis
- 3-axis magnetic electronic compass.
- Precise heading information.
- Operating Voltage:Â 3 -5 V DC.
- Driver Chip:Â HMC5883L.
- Communication:Â I2C protocol.
- Measuring range: ± 1.3-8 Gauss.
₹118.00 (excl. GST)GY-271 HMC5883L 3-axis Electronic Compass Module
₹118.00 (excl. GST) -
Weighing Load Cell Sensor 1Kg for Electronic Kitchen Scale YZC-131 With Wires
Load Cell Sensor 1Kg
- Weighing Range: 0 ~ 1 kg.
- Rated Output: 1.0 ± 0.1mV / V.
- Non Linear Output: ± 0.03% F.S.
- Input Impedance: 1066 ± 10% Ω.
- Output Impedance: 1000 ± 10% Ω.
- Insulation Resistance: 2000 MΩ.
₹116.00 (excl. GST)Weighing Load Cell Sensor 1Kg for Electronic Kitchen Scale YZC-131 With Wires
₹116.00 (excl. GST) -
CNC shield V3 for Engraving Machine 3D Printer A4988 DRV8825 driver expansion board
Features :
- Coolant enable
- Uses removable Pololu A4988 compatible stepper drivers. (A4988, DRV8825 and others) (Not Included)
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
- Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
- Please note that this is an unassembled kit and needs soldering.
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- PWM Spindle and direction pins
- 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
₹116.00 (excl. GST) -
ESP-12F ESP8266 Wifi IOT Module
- Communication interface voltage: 3.3V
- Working current: 240mA(MAX)
- Serial port baud rate: 115200 (default), can be modified to other values by AT command
- Serial communication format: 8N1
- Wireless Network Mode: station / softAP / SoftAP + station
- Wireless criteria: 802.11 b / g / n
- WIFI @ 2.4 GHz, support for WPA / WPA2 security mode
- +19.5dBm output power
₹115.00 (excl. GST)ESP-12F ESP8266 Wifi IOT Module
₹115.00 (excl. GST) -
Expansion Testing Interface Board for Microcontrollers
Features:
Input Output Board for Arduino 8051 AVR Raspberry Pi
8 LEDs and 4 Switches
5V Relay, Buzzer for Output test
TSOP, LDR and LM35D Temperature Sensor for Input Testing
Potentiometer for Varying Sensitivity.₹115.00 (excl. GST)Expansion Testing Interface Board for Microcontrollers
₹115.00 (excl. GST)