-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)
-
DC Male Power Jack, Adapter Connector Plug For CCTV, Camera -(2.1 x 5.5mm)Pack of 2
DC Male Power Jack
Specifications:
- 2.1 x 5.5mm CCTV Camera DC Power Plug Connector.
- DC Power Plug with plastic construction and strain relief.
- This 2.1 x 5.5mm Power Plug features one power connector end DC plug male to another end terminal for CCTV camera connected.
- The internal diameter of the plug: 2.1mm
- The external diameter of the plug: 5.5mm
₹36.00 (excl. GST) -
DC Mini Horizontal Submersible Pump
- Operating Voltage : 2.5 ~ 6V
- Operating Current : 130 ~ 220mA
- Flow Rate : 80 ~ 120 L/H
- Maximum Lift : 40 ~ 110 mm
- Outlet Outside Diameter: 7.5 mm
₹35.00 (excl. GST)DC Mini Horizontal Submersible Pump
₹35.00 (excl. GST) -
DC Motor 2000 RPM – 3V to 6V
Features:
Length: 25mm
Diameter:21mm
Shaft Diameter:2mm
Shaft Length:9mm
Voltage:3-5V₹20.00 (excl. GST)DC Motor 2000 RPM – 3V to 6V
₹20.00 (excl. GST) -
DC Power Female Jack Adapter Connector Plug For CCTV Camera- (2.1*5.5mm )
DC Power Female Jack Adapter
Female Jack Description:
- 5.5mm x 2.1mm Female power plug connector.
- The external diameter of the plug: 5.5mm.
- The internal diameter of the plug: 2.1mm.
- Dimension: 38mm(L) x 14mm(W) x 13mm(H).
₹40.00 (excl. GST)DC Power Female Jack Adapter Connector Plug For CCTV Camera- (2.1*5.5mm )
₹40.00 (excl. GST) -
DC Power Jack-Female Connector with 2 pin Screw Terminal – Pack of 2
- Connector Type: DC 5.5/2.1mm
- Connector type DC mains
- Electrical mounting screw terminal
- Length of metal part 12mm
- Spatial orientation straight
₹47.00 (excl. GST)DC Power Jack-Female Connector with 2 pin Screw Terminal – Pack of 2
₹47.00 (excl. GST) -
DC Pump 24V 150PSI for Mist Fog Spray in Sanitizer Dispenser Tunnel
- Watering configuration: much the same, additional sprinklers and timers are required
- The price is the price of a pump, without other accessories
- Maximum pressure: 0.48MP.
₹1,500.00 (excl. GST)DC Pump 24V 150PSI for Mist Fog Spray in Sanitizer Dispenser Tunnel
₹1,500.00 (excl. GST) -
DC PWM Motor Speed Controller
- The maximum output power:30W
- Input supply voltage:1.8V-15VDC
- The Maximum continuous output current:2A
- Duty Cycle adjustable:0%-100%
₹65.00 (excl. GST)DC PWM Motor Speed Controller
₹65.00 (excl. GST) -
DC Straight BO Motor for Smart Car Robot
- Operating Voltage(VDC): 3~12
- Shaft Length (mm): 8.5
- Shaft Diameter (mm): 5.5 (Double D-type)
- No Load Current: 40-180mA.
- Rated Speed(After Reduction): 300 RPM
- Rated Torque: 0.35 Kgcm
₹34.00 – ₹42.00 (excl. GST)DC Straight BO Motor for Smart Car Robot
₹34.00 – ₹42.00 (excl. GST) -
DC5V Humidifier USB Spray Module DIY Incubation Experiment Equipm 108KHz
- Work Voltage:DC 4.5V~5.0V
- Work Power:2W
- Work Frequency:108KHz(+/-3KHz)
- Come with a driver
- Power-ON trigger work
- 108KHz high frequency oscillator
₹216.00 (excl. GST)DC5V Humidifier USB Spray Module DIY Incubation Experiment Equipm 108KHz
₹216.00 (excl. GST) - Work Voltage:DC 4.5V~5.0V
-
Desoldering Pump Tool
- One-handed solder sucker with powerful suction whether you are right or left-handed, you can using the desoldering pump by just cocking it and pressing the trigger button with one hand when you are ready, the desoldering pump designed with double ring double open and “vacuum” button, which make the sucking power awesome
₹85.00 (excl. GST)Desoldering Pump Tool
₹85.00 (excl. GST) -
DFRobot Gravity I2C Oxygen Sensor
Features:
- High sensitivity
- I2C Interface
- Compatible with both 3.3V and 5V micro-controllers
- Polarity protection
₹3,800.00 (excl. GST)DFRobot Gravity I2C Oxygen Sensor
₹3,800.00 (excl. GST) -
DHT11 Temperature and Humidity Sensor Module
- DHT11 sensor with PCB and LED indicator; 3 to 5V power and I/O, 4 pins with 0.1″ spacing
- The board has pre-built 4.7K or 10K resistor, which you will need to use as a pull-up from the data pin to VCC.
- 2.5mA max current use during conversion (while requesting data)
- Good for 20-80% humidity readings with 5% accuracy
- Good for 0-50°C temperature readings ±2°C accuracy.
₹45.00₹92.00(excl. GST)DHT11 Temperature and Humidity Sensor Module
₹45.00₹92.00(excl. GST)
