-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)
-
12 in 1 DIY Sensor Kit
Sensors Included:
PIR Motion Sensor HCSR501, Touch Sensor, Rain Sensor, Hear beat Sensor, Flame Sensor, Soil Moisture Sensor, Sound Sensor, Ultrasonic Sensor HCSR04, Temperature and Humidity Sensor DHT11, LDR Sensor, IR Sensor, Tilt Sensor.
₹550.00₹1,100.00(excl. GST)12 in 1 DIY Sensor Kit
₹550.00₹1,100.00(excl. GST) -
MQ9 Gas Carbon Monoxide, Methane and LPG Gas Sensor Module
- Good sensitivity to CO/Combustible Gas
- High sensitivity to Methane, Propane, and CO
- Long life and low cost
- Simple drive circuit
- Input voltage: DC 5±0.2V
- Current Consumption: 150mA
₹88.00 (excl. GST)MQ9 Gas Carbon Monoxide, Methane and LPG Gas Sensor Module
₹88.00 (excl. GST) -
MQ5 Gas Sensor Detector Module
- Operating Voltage: 5V DC
- High sensitivity to LPG, natural gas, town gas.
- Small sensitivity to alcohol, smoke.
- Stable and long life.
- Simple drive circuit.
- Fast response.
- Has a long life and reliable stability
- Fast response and recovery characteristics Applications of MQ6 LPG Gas Sensor Module:-
- Gas leak detection system
- Fire/Safety detection system
- Domestic gas leakage detector
- Industrial Combustible gas detector
- Portable gas detector
- Gas leak alarm
- Gas detector
₹88.00 (excl. GST)MQ5 Gas Sensor Detector Module
₹88.00 (excl. GST) -
