-
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC: 3.3V-5V
GND: GND
DO: Digital output interface(0 and 1)
AO: Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Capacitive Soil Sensor V2.0 Wholesale/B2B (Pack of 25)
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹750.00 (excl. GST)Capacitive Soil Sensor V2.0 Wholesale/B2B (Pack of 25)
₹750.00 (excl. GST) -
Waveshare 7inch Capacitive Touch Screen LCD (B)
Features:
- 800×480 High-Resolution Display
- Capacitive Touch Control
- HDMI Interface for Display, USB Interface for Touch Control
- Supports Raspberry Pi, comes with Raspbian driver (Works directly with Raspbian), and Ubuntu Image
- Supports Banan Pi, Banana Pro, comes with LUbuntu, Raspbian Image
- Supports BB Black, comes with Angstrom Image
- Not only SBC’s, but it can also work with any computer display with HDMI Interface, Touch interface will not work in that case.
- Backlight control, for lower power consumption.
₹4,200.00₹4,600.00(excl. GST)Waveshare 7inch Capacitive Touch Screen LCD (B)
₹4,200.00₹4,600.00(excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
ESP8266 ESP-01/ESP-01S – DHT11 Temperature Humidity Sensor Module
- This DHT11 temperature and humidity sensor shield is specially designed for ESP8266 ESP-01 ESP-01S development board.
- On-board 8pin socket enable you plug the wifi transceiver to the board directly perfect for DIY your wireless temperature/humidity webserver system.
- Working Voltage: DC 3.7 – 12V
- The weight of about 10 grams
- Package Included: 1 X DHT11 Humidity Temperature Sensor
₹130.00 (excl. GST)ESP8266 ESP-01/ESP-01S – DHT11 Temperature Humidity Sensor Module
₹130.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST)
-
1S 2A BMS Board 3.7V 18650 Lithium Battery Protection Board
Features:
- Easy to use
- Color: Green
- The internal resistance difference is not more than 5mQ
- BMS Li-ion Battery Protection Board
- The tolerance is less than 30mAh
- Single-cell consumption of battery (self-consumption): ≤3uA
- In this MOSFET are employed to do the monitoring task which protects our battery cells from overcharge
Precautions:1. Before installing the protection board, the battery should be matched well (the voltage difference between each battery should not be 0.05V, the internal resistance difference is not more than 5mQ, the tolerance is less than 30mAh), the smaller the battery voltage difference, the better the protection board will work. .2. The batteries are connected in parallel and then connected in series, and the welding is correct (18650 battery nickel spot welding, other batteries are soldered), do not screw, easy to burn the protection board IC.3. If it is an old battery change board, please pay attention: Please confirm the battery is normal before buying?4. When installing, use a multimeter to check whether the voltage of each string is the same. The performance failures with a difference of more than 1.0V are: running not far, starting and powering off, charging time is short, basically the battery core problem is more. The failure of the protection board is as follows: the battery cannot be charged, and the battery has a voltage and cannot be discharged.₹15.00 (excl. GST)1S 2A BMS Board 3.7V 18650 Lithium Battery Protection Board
₹15.00 (excl. GST) -
₹15.00 (excl. GST)6K8 Wire Wound Resistor 10W ±5%
₹15.00 (excl. GST) -
170 Points Mini Bread Board
- 170 Tie-points for Arduino Raspberry Pi
- Colour May Vary
- Great addition to your hobby craft tool kit
- Perfect product for your saftey and lab supply
- ABS Plastic material
₹15.00₹25.00(excl. GST)170 Points Mini Bread Board
₹15.00₹25.00(excl. GST) -
ULN2003 Stepper Motor Driver IC
- 500-mA-Rated Collector Current (Single Output)
- High-Voltage Outputs: 50 V
- Output Clamp Diodes
- Inputs Compatible With Various Types of Logic
- Relay-Driver Applications
₹15.00 (excl. GST)ULN2003 Stepper Motor Driver IC
₹15.00 (excl. GST) -
TIP32C PNP Bipolar Power Transistor
- Polarity: PNP
- Transistor type: BJT single power
- Pin counts: 3
- package contains: 1 x transistor IC
₹15.00 (excl. GST)TIP32C PNP Bipolar Power Transistor
₹15.00 (excl. GST) -
Piezo Electronic Buzzer Beep 9v-12v Buzzer Electromagnetic
Rated Voltage: 5VDC
Operating Voltage: 4-8VDC
Max.Rated Current: 40mA
Coil Resistance(DC): 45±5Ω
Coil Resistance(DC): 80Ω
Min.Sound Pressure Level: 85dB/10cm
Resonant Frequency: 2400Hz
Operating Temperature: -20～+70℃
Storage Temperature: -30～+80℃₹15.00 (excl. GST)Piezo Electronic Buzzer Beep 9v-12v Buzzer Electromagnetic
₹15.00 (excl. GST) -
₹15.00
₹20.00(excl. GST)TTP223 Touch Sensor Module
₹15.00₹20.00(excl. GST) -
FRC connector female 40 pin (Pack of 2)
-
Features/Specs:
- Gender: Female
- Connector Type: IDC
- Number Of Contacts: 40
- Number Of Rows: 2
- Pitch: 2.54mm
- Current Rating: 2A
- Mounting Type: Cable Mount
- Contact Material: Phosphor Bronze
- Minimum Operating Temperature: -65°C
- Maximum Operating Temperature: +105°C
- Housing Material: Thermoplastic
- Contact Plating: Nickel-plated terminals
- Color: Black
₹14.00 (excl. GST)FRC connector female 40 pin (Pack of 2)
₹14.00 (excl. GST) -
-
FRC connector male 40 pin (Pack of 2)
-
Features/Specs:
- 40 Pin Box Header Male Straight
- Arrangement: 20 x 2 pins
- Pitch: 2.54 mm
- Current Rating: 3 A max
- Working Voltage: 250V AC
- Gender: Male
- Connector Type: IDC
- Current Rating: 3A
- Insulation Resistance: 1000MΩ MIN
- Contact Impedance: 15mΩ MAX
- Mounting Type: PCB Mount
- Contact Material: Phosphor Bronze
- Operating Temperature: -25°C ~ +105°C
- Housing Material: Thermoplastic
- Contact Plating: Nickel-plated terminals
- Color: Black
₹14.00 (excl. GST)FRC connector male 40 pin (Pack of 2)
₹14.00 (excl. GST) -
-
TIP122 Darlington NPN Transistor
Collector-Emitter Voltage (Vce) (V) 45 Emitter-Base Voltage (Veb) (V) 6 Collector Current (DC) (A) 100m Junction Temperature (°C) 150 Storage condition (℃) -65 to 150 ₹14.00 (excl. GST)TIP122 Darlington NPN Transistor
₹14.00 (excl. GST) -
Lithium Battery Charging Protection Board-5V Step-Up Power Module
Lithium Battery Charging Protection Board
- BAT Discharging Stop Voltage:2.9V
- Discharging Efficiency:85%(input 3.7V output 5V/1A)
- Charging and discharging indication
- Internally installed charging and discharging power MOS
- Preset 4.2V charging voltage, precision ±1%
- Max 8uA standby current
- Integration charging management and discharging management
- Intelligent temperature control and overtemperature protection
- Integration output overvoltage protection, short circuit protection, overload protection
₹13.00 (excl. GST)Lithium Battery Charging Protection Board-5V Step-Up Power Module
₹13.00 (excl. GST) -
Voltage Detection Sensor Module 25V
Features :
- Output Interface: “+ ” connected 5/3.3V, “-” connected GND, “s” connected Arduino AD pins
- DC input interface: red terminal positive with VCC, negative with GND
- You can also use the IICLCD1602 LCD to display voltage.
- By 3P connector, connect this module with the expansion of board Arduino, not only makes it easier for you to detect voltage battery.
₹13.00 (excl. GST)Voltage Detection Sensor Module 25V
₹13.00 (excl. GST)
