-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)
-
Stanley Hot Glue Gun 69-GR20B
Secure your wooden furniture or the fabric cover of your cushions with the Stanley 69-GR20B Standard Temperature Corded
₹780.00 (excl. GST)Stanley Hot Glue Gun 69-GR20B
₹780.00 (excl. GST) -
1200W DC-DC Boost Module 20A Step-up Boost Convertor 8-60V to 12-80V Adjustable Power Supply
- 1200W DC to DC step-up power supply module for electronic equipment with adjustable power supply module where you can set the output voltage according to device.
- Input and output are designed with screw terminals for convenient wire connection and disconnection.
- Input voltage: 8-60V
- Output voltage: 12-80V continuously adjustable
₹795.00 (excl. GST) -
Orange 7.4V 1000mAh 30C 2S Lithium Polymer Battery Pack
Features :
- Product Type: Lithium Polymer Battery Pack
- The Orange LiPo battery has matched resistance.
- Good Temperature Control.
- Minimum weight in Class
₹795.00₹899.00(excl. GST)Orange 7.4V 1000mAh 30C 2S Lithium Polymer Battery Pack
₹795.00₹899.00(excl. GST) -
Junior Hacksaw Blades – 12 inch
A pack of ten 150mm blades made from a strong but flexible carbon steel to ensure extra long life.
₹800.00 (excl. GST)Junior Hacksaw Blades – 12 inch
₹800.00 (excl. GST) -
PCB Power Drill Machine
Features:
- Model – MB140
- Key-pin chuck
- Chuck capacity 0.4 to 1.0mm; 2.1 to 2.5mm
- Operating Voltage – 0 to 18 volts (D.C.)
- Ergonomic design includes a pencil grip for comfort
- Motor is fan cooled for long periods of use and longevity
- Overall length: 170mm (approx)
- RPM: 0 – 30,000 rpm
- Collete – (0mm) 1piece; (2.3mm) 1piece
- Weight: ~275grams
₹800.00 (excl. GST)PCB Power Drill Machine
₹800.00 (excl. GST) -
BMS 8S 24V 20A DALY Lifepo4 Battery Management System
- Model: 8S 24V 20A
- Battery Type: Lithium Battery
- No.of cells in series: 8s
- Discharge Current: 20A
- Charge Current: 10A
₹800.00 (excl. GST)BMS 8S 24V 20A DALY Lifepo4 Battery Management System
₹800.00 (excl. GST) -
NEEMA 17-JK42HS48-1684-0.44N-m D Type 5.5Kg
Features :
- The input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- It provides good starting, stopping, and reversing.
- Control of this motor is less costly because of the exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
₹825.00 (excl. GST)NEEMA 17-JK42HS48-1684-0.44N-m D Type 5.5Kg
₹825.00 (excl. GST) -
3S 100A 12.6V Li-ion Lithium 18650 Battery BMS PCM Protection Board with Balance
- Charging voltage: 12.6V-13V
- Size: 70*60*8.5mm
- Over-discharge voltage range: 2.5±0.05v
- Upper limit working current: 100A (pay attention to heat dissipation)
- Working temperature: -40~+50°C
- Effective life: more than 30,000 hours
₹830.00 (excl. GST)3S 100A 12.6V Li-ion Lithium 18650 Battery BMS PCM Protection Board with Balance
₹830.00 (excl. GST) -
12V 3.5A 4000ml/min Liquid Diaphragm Pump
Features:
- Self-Priming
- Low Power Consumption
- Long Life
- Can Run in Dry Condition
₹835.00 (excl. GST)12V 3.5A 4000ml/min Liquid Diaphragm Pump
₹835.00 (excl. GST) -
SeeedStudio Grove GSR sensor
SeeedStudio
Features:
- Detects conductance of the skin
- Finger Straps for electrodes
₹840.00 (excl. GST)SeeedStudio Grove GSR sensor
₹840.00 (excl. GST) -
Pro-Range INR 18650 11.1V 2000mAh 3C 3S1P Li-Ion Battery Pack with DC Jack Male & Female
- Nominal Capacity (mAh): 2000
- Nominal Voltage (v): 11.1
- Max Charging Voltage (v): 12.6
- Charge Port: DC Female
- Discharge Port: DC Male
₹840.00 (excl. GST) -
Arduino Mega 2560 R3 with USB Cable Compatible with Arduino
- Microcontroller: ATmega2560
- Operating Voltage: 5V
- Input Voltage (recommended): 7-12V
- Input Voltage (limits): 6-20V
- Digital I/O Pins: 54 (of which 15 provide PWM output)
- Analog Input Pins: 16
- DC Current per I/O Pin: 40 mA
- DC Current for 3.3V Pin: 50 mA
- Flash Memory: 256 KB of which 8 KB used by bootloader
- SRAM: 8 KB
- EEPROM: 4 KB
- Clock Speed: 16 MHz
- USB Host Chip: MAX3421E
- Length:101.98mm/4.01in
- Width:53.63mm/2.11in
- Height:15.29mm/0.60in
₹850.00₹1,475.00(excl. GST)Arduino Mega 2560 R3 with USB Cable Compatible with Arduino
₹850.00₹1,475.00(excl. GST)
