-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)
-
LM6UU 6 MM Linear Motion Bearing
LM6UU 6 MM Linear Motion Bearing
Features :
- Outer Casing: Chromium Steel
- Low friction, optimum loading capacity, long life.
- It has linear bearing ball cage, hardened coat at both end rings.
- No worry if replacement of any worn part.
- Low noise even in high-speed operation.
₹42.00 (excl. GST)LM6UU 6 MM Linear Motion Bearing
₹42.00 (excl. GST) -
LM741 Op-amp IC
- Two Independent, High-Gain, Frequency Compensated Op-Amps
- Input Offset Voltage: 2 mV
- Input Offset Current: 20 nA
- Input Bias Current: 80 nA
- Supply Current: 1.7 mA
₹8.00 (excl. GST)LM741 Op-amp IC
₹8.00 (excl. GST) -
LM741N PDIP-8 Operational Amplifier (Pack of 3 ICs)
  LM741N
- Overload protection on the input and output
- No latch-up when the common mode range is exceeded
- Applications: Audio, Communications & Networking, Signal Processing
₹27.00 (excl. GST)LM741N PDIP-8 Operational Amplifier (Pack of 3 ICs)
₹27.00 (excl. GST) -
₹100.00 (excl. GST)Lm75A Temperature Sensor Development Board Module I2C Interface Hi-Q
₹100.00 (excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
LX-103 Light Meter Luxmeter, Measures Up-To 2,00,000 LUX/20,000 FC
Features Of HTC LX-103 Digital Lux Meter:
- Large Range up to 200000Lux
- Large LCD Display with Back Light and Bar Graph
- Auto Power Off
- MAX/MIN and Data Hold
₹2,015.00 (excl. GST)LX-103 Light Meter Luxmeter, Measures Up-To 2,00,000 LUX/20,000 FC
₹2,015.00 (excl. GST) -
M274 360 Degree Rotary Encoder Brick Sensor Module
M274 360 Degree Rotary Encoder
- Model : KY-040.
- Type : Incremental Encoder.
- Cycles per revolution (CPR) : 20.
- Working voltage : 0 – 5V.
- Material : PCB + Brass.
- Mounting Nut Thread diameter: 6.6mm
- Weight : 10 gm.
₹32.00 (excl. GST)M274 360 Degree Rotary Encoder Brick Sensor Module
₹32.00 (excl. GST) -
M3 x 10mm CHHD Bolt and Nut Set-25 pcs.
Bolt and Nut Set
- Type: M3 (3.0mm Diameter)
- Material: Mild Steel
- Bolt Head Style: Slotted & Round
- Pack Quantity: 25 sets.
- Nut Type: Hex
₹48.00 (excl. GST)M3 x 10mm CHHD Bolt and Nut Set-25 pcs.
₹48.00 (excl. GST) -
M3 x 25mm CHHD Bolt and Nut Set-20pcs.
M3 x 25mm
- Type: M3 (3.0mm Diameter)
- Material: Mild Steel
- Bolt Head Style: Slotted & Round
- Pack Quantity: 20 sets.
- Nut Type: Hex
₹48.00 (excl. GST)M3 x 25mm CHHD Bolt and Nut Set-20pcs.
₹48.00 (excl. GST) -
M3 X 8mm Bolt and Nut Set-25 pcs.
M3 X 8mm
- Type: M3 (3.0mm Diameter)
- Material: Mild Steel
- Bolt Length: 8mm
- Bolt Head Style: Slotted & Round
- Pack Quantity: 25 sets.
₹48.00 (excl. GST)M3 X 8mm Bolt and Nut Set-25 pcs.
₹48.00 (excl. GST) -
M4 x 20mm CHHD Bolt and Nut Set-20Pcs.
M4 x 20mm
- Type: M4 (4.0mm Diameter)
- Material: Mild Steel
- Bolt Head Style: Slotted & Round
- Pack Quantity: 20 sets.
- Nut Type: Hex
₹48.00 (excl. GST)M4 x 20mm CHHD Bolt and Nut Set-20Pcs.
₹48.00 (excl. GST) -
Magnet Experiment Kit
Magnet Experiment Kit
Features:
- The same pole repels but the opposite pole attracts can do a variety of experiments
- The kit is easy to carry and store, making it convenient for you to experiment.
₹310.00 (excl. GST)Magnet Experiment Kit
₹310.00 (excl. GST)
