-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)
-
2 Channel 5V Relay Module
- The module using Songle relay control.
- AC voltage 250V, AC current 10A, maximum DC voltage 30V DC current maximum 10A.
- Power indicator (green), Two ways of relay status indicator light (red).
- Using 8550 transistor-driven, strong driving ability.
- Has the fixed bolt hole and easy installation.
₹55.00 (excl. GST)2 Channel 5V Relay Module
₹55.00 (excl. GST) -
470 Ohm Carbon Film Resistor- Pack of 50 pcs
- Resistance Value: 470 Ohms
- Rated Power: 0.25 Watt (1/4W); Tolerance : +/- 5%
- Carbon Film Resistor – Through Hole; Flame Retardant Coating
- Stiff 24 gauge leads (0.022 inches, 0.55 mm) perfect for solderless plug-in breadboards
- Package Include 10 x 470 Ohm (Note: Color of resistor may change, so please contact us if you need specific color resistors
₹50.00 (excl. GST)470 Ohm Carbon Film Resistor- Pack of 50 pcs
₹50.00 (excl. GST) -
Red R13-507 16mm No Lock Push, Button Momentary Switch 3A, 250V
- Model: R13-507-M-5S
- Material: Plastic, metal
- Terminals: 2 Pin
- Action Type: Momentary Action, Push and Hold – ON, Release – OFF
₹15.00 (excl. GST)Red R13-507 16mm No Lock Push, Button Momentary Switch 3A, 250V
₹15.00 (excl. GST) -
0.1MM Copper Soldering Solder PPA Enamelled Repair Reel Wire
- Wire Diameter: 0.1 mm.
- Length: about 15m
- Color: Copper
- Melting point: 361 ° F / 183 ° C
- Material: Copper / Copper Alloy
- Spool Size: 3.1cm x 3.1cm x 1.9cm.
₹37.00 (excl. GST)0.1MM Copper Soldering Solder PPA Enamelled Repair Reel Wire
₹37.00 (excl. GST) -
2 Channel Logic Level Converter 3.3V 5V TTL
- Material: Plastic + metal
- Portable, small, easy to use.
- Comes with 2 rows of 6pin, unsoldered.
- The compatible breadboard can be directly inserted into the breadboard.
₹37.00 (excl. GST)2 Channel Logic Level Converter 3.3V 5V TTL
₹37.00 (excl. GST) -
DB9 Female Welded Connector
- Solder cup configuration for longevity.
- Nickel-plated terminals.
- Gold plates pins.
- Good quality.
₹18.00 (excl. GST)DB9 Female Welded Connector
₹18.00 (excl. GST) -
DB9 Male Welded Connector
- Solder cup configuration for longevity.
- Nickel-plated terminals.
- Gold plates pins.
- Good quality.
₹20.00 (excl. GST)DB9 Male Welded Connector
₹20.00 (excl. GST) -
Johnson Geared Motor (Grade B) 200 RPM
- Product: Johnson Geared Motor (Grade B) 200 RPM
- Rated Base Motor RPM: 18000
- Gear Material: Metal
- Rated Speed (RPM): 200
- Operating Voltage (VDC): 6 ~ 18
₹338.00 (excl. GST)Johnson Geared Motor (Grade B) 200 RPM
₹338.00 (excl. GST) -
Johnson Geared Motor (Grade B) 10 RPM
- Base Motor RPM: 18000
- Operating Voltage: 6-18 V
- Rated Voltage: 12 V
- Rated Torque: 11.7 kg-cm
- Stall Torque: 46 kg-cm
- Gearbox Dimensions: 30×37 (LxW) mm
₹369.00 (excl. GST)Johnson Geared Motor (Grade B) 10 RPM
₹369.00 (excl. GST) -
AC Voltage Sensor Module ZMPT101B (Single Phase)
- Voltage – 250V
- Easy PCB mounting
- Good consistency
- Widely acclaimed
₹71.00 (excl. GST)AC Voltage Sensor Module ZMPT101B (Single Phase)
₹71.00 (excl. GST) -
ERM Coin Vibration Motor, 8 mm Dia. ,2 mm Width
- Product: ERM Coin Vibration Motor
- Operating voltage: 2.5-3.3 VDC
- Starting Voltage: 2.3 mAx
- Rated Current: 80.0 Max
- Rated RPM.: 9000 Min
₹40.00 (excl. GST)ERM Coin Vibration Motor, 8 mm Dia. ,2 mm Width
₹40.00 (excl. GST) -
TowerPro MG995 Plastic Gear Servo Motor (180° Rotation)-Standard Quality
- Model: MG995
- Weight: 55 gm
- Operating voltage: 4.8V~ 7.2V
- Servo Plug: JR
- Stall torque @4.8V : 10 kg-cm
- Stall torque @6.6V : 12 kg-cm
₹187.00 (excl. GST)TowerPro MG995 Plastic Gear Servo Motor (180° Rotation)-Standard Quality
₹187.00 (excl. GST)
