-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)
-
Resistor Kit 150 Pieces 30 Values 1/4W for Electronics DIY
- Carbon film assorted resistors
- 30 values
- Quantity: 150 pieces (5 each)
- Tolerance: 5%
- Power Rating: 0.25 wat
₹150.00 (excl. GST)Resistor Kit 150 Pieces 30 Values 1/4W for Electronics DIY
₹150.00 (excl. GST) -
12V 2A DC Power Adapter
- Universal
- Power Consumption: 60 W
- Power Cord Included
₹150.00 (excl. GST)12V 2A DC Power Adapter
₹150.00 (excl. GST) -
5V 2Amp Adapter (5 V – 2 A DC SMPS)
- Compatible with Dth,STB,CCTV,toys,broad band,laptop,DVD,tablet,TV tuner card,cordledd phones,LCD moniter,scanner,cell phone,printers
- Dual Output Pin: DC Pin + Sony Pin
- Ideal for CCTV Cameras / Routers / Modems / Cordless Phones / Set Top Boxes / Wireless Devices / POS Machines etc.
- Simple to use, just plug-in, charge up and play
- The official power adapter allows you to charge your handheld console with any two-pin socket
- Compatible with Dth,STB,CCTV,toys,broad band,laptop,DVD,tablet,TV tuner card,cordledd phones,LCD moniter,scanner,cell phone,printers
- Dual Output Pin: DC Pin + Sony Pin
- Ideal for CCTV Cameras / Routers / Modems / Cordless Phones / Set Top Boxes / Wireless Devices / POS Machines etc.
₹150.00 (excl. GST)5V 2Amp Adapter (5 V – 2 A DC SMPS)
₹150.00 (excl. GST) -
150W DC-DC Boost Converter 10-32V to 12-35V 6A Step-Up Adjustable Power Supply
Features :
- The non-isolated step-up power conversion module
- Onboard LED illuminates when the voltage is applied to the module
- Equips Multi-turn Potentiometer.
- Easy to drive 65W 90W dual-core notebook.
- The output voltage is continuously adjustable on OUT+ and OUT- screw terminals (Output voltage must be greater than input voltage)
₹150.00 (excl. GST)150W DC-DC Boost Converter 10-32V to 12-35V 6A Step-Up Adjustable Power Supply
₹150.00 (excl. GST) -
₹150.00 (excl. GST)
Rubber Band Powered Aircraft Model Kits Toy
₹150.00 (excl. GST) -
Portable Resistor LED Potentiometer Kit for UNO R3
- 1 sets Handy Portable Resistor Kit for Arduino Starter Kit UNO R3 LED potentiometer tact switch pin header
- High Quality kit for arduino
₹150.00 (excl. GST)Portable Resistor LED Potentiometer Kit for UNO R3
₹150.00 (excl. GST) -
Mini Solar Powered Toy Car
- DIY Mini Solar Powered Toy Car Kit For Children Educational Gadget Hobby Funny
- Material: ABS, metal
- Net Weight: 35g
- Product size: 8 x 7.5 x 3.2cm
- Solar panel: 1V, 80mA
- Dimensions and Weight:8.00 x 7.50 x 3.20 cm / 3.15 x 2.95 x 1.26 inches
₹150.00₹170.00(excl. GST)Mini Solar Powered Toy Car
₹150.00₹170.00(excl. GST) -
1-8S Lipo Battery Voltage Tester
Features :
- Input: 1S-8S Battery
- Battery type: Lipo/LiFe/Li-ion/LiMn
- It has a Buzzer Alarm for low voltage indication.
- Useful for measuring each cell voltage.
- It has a mode button at the top for setting the desired voltage value.
₹154.00 (excl. GST)1-8S Lipo Battery Voltage Tester
₹154.00 (excl. GST) -
ADXL345 3 Axis Accelerometer Gravity Module
- On-board ADXL345, it’s a low cost cap-based accelerometer sensor
- Support 5V/3.3V voltage input, onboard RT9161, better performance than 1117, faster load the appropriate speed, it is ideal for high noise power supply environment
- Common Pins were lead out, Pin distance is standard 100mil (2.54mm), compatible for your new system
- Communication: I2C
₹155.00 (excl. GST)ADXL345 3 Axis Accelerometer Gravity Module
₹155.00 (excl. GST) -
MG90S Metal Geared Micro Servo Motor
Applications:
Used as actuators in many robots like Biped Robot, Hexapod, robotic arm etc..
Commonly used for steering system in RC toys
Robots where position control is required without feedback
Less weight hence used in multi DOF robots like humanoid robots
Can be used in DIY Kit for hobby projects₹155.00 (excl. GST)MG90S Metal Geared Micro Servo Motor
₹155.00 (excl. GST) -
Aluminum GT2 Timing Pulley 40 Tooth 5mm Bore For 6mm Belt
This pulley has 40Â teeth and a 5mm inner bore. Two set screws can be used to attach it firmly to any 5mm diameter shaft. Full aluminum construction means these are very light and very durable.
Specifications-
- Material: Aluminum.
- No. of teeth: 40.
- Outer Diameter: 27 mm.
- Inner Bore Diameter: 5mm.
₹156.00 (excl. GST)Aluminum GT2 Timing Pulley 40 Tooth 5mm Bore For 6mm Belt
₹156.00 (excl. GST) -
Micro HDMI to HDMI Cable
Features:
- New version 1.4 HDMI to micro HDMI cable
- Supports 480i ,480p, 720p, 1080i, 1080p, 1440p resolution
- Backward compatible with all previous HDMI standards
- HDMI Head: Skidproof gold-plated plug head HDMI TO Micro HDMI
- Wire: Silver coated copper wire inside to reduce interference
- Fully HDCP compliant to Provide the highest level of signal quality
- Supports multiple audio formats, from stereo to multi-channel sound, Perfect for both high-definition video and standard video formats
- Shielded for maximum protection from RFI and EMI interference
To connect this cable with Mobile Phone or Tablets with Micro-USB or C-type ports you will need Micro-USB or C-type to HDMI converter Â
₹158.00 (excl. GST)Micro HDMI to HDMI Cable
₹158.00 (excl. GST)
