-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)
-
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST) -
Hi Link HLK PM01 5V/3W Switch Power Supply Module
Features:
- Meet UL, CE requirements,
- Ultra-thin, ultra-small
- All voltage input (AC: 90 ~ 264V)
- Low ripple and low noise
- Output overload and short circuit protection
- High efficiency, high power density
- The product is designed to meet the requirements of EMC and Safety Test
- Low power consumption, environmental protection, no-load loss <0.1W
Environmental conditions:
- Technical indicators: Single bit
- Working temperature: – 20-60 +degree
- Storage temperature: + 80-40 -degree
- Relative humidity: 5-95%
- The cooling way: Natural cooling
- The atmospheric pressure: 80-106Kpa
- The altitude: 2000M or less.
₹164.00 (excl. GST)Hi Link HLK PM01 5V/3W Switch Power Supply Module
₹164.00 (excl. GST) -
Hi-Link Switch Power Supply Module (HLK PM01 5V/3W)
Hi-Link Switch Power Supply Module
Environmental conditions:
- Technical indicators: Single bit
- Working temperature: – 20-60 +degree
- Storage temperature: + 80-40 -degree
- Relative humidity: 5-95%
- The cooling way: Natural cooling
- The atmospheric pressure: 80-106Kpa
- The altitude: 2000M or less.
₹161.00 (excl. GST)Hi-Link Switch Power Supply Module (HLK PM01 5V/3W)
₹161.00 (excl. GST) -
High Current Active Alarm Buzzer Driver Module
- Operating voltage 3.3V-5V
- PCB Dimension: 3.1cm*1.3cm.
- Color: Blue
- Easy to use
₹32.00 (excl. GST)High Current Active Alarm Buzzer Driver Module
₹32.00 (excl. GST) -
High Sensitivity Sound Sensor Module
- Main chip: LM393, Electret condenser microphone
- Working voltage:Â DC 3.3-5V
- Induction distance is 0.5M
- Signal output Indication
- Single channel signal output
- The output effective signal is low level.
.
₹35.00₹40.00(excl. GST)High Sensitivity Sound Sensor Module
₹35.00₹40.00(excl. GST) -
High Voltage Ceramic Capacitor Kit-300pcs
- Capacity loss has high stability with temperature and frequency
- Special series connection structure is suitable for high voltage and extremely long-term working reliability
- High current climb rate and suitable for high-current loop non-inductive structure
- Values- 3KV0.1nF,3KV0.22nF, 3KV1nF,3KV2.2nF, 3KV4.7nF, 3KV10nF,2KV0.47nF,2KV0.56nF,2KV0.68nF,2KV1nF,2KV1.5nF,2KV3.3nF, 1KV2.2nF, 1KV10nF,1KV22nF
₹650.00 (excl. GST)High Voltage Ceramic Capacitor Kit-300pcs
₹650.00 (excl. GST) -
HM-10 BLE Bluetooth 4.0 CC2541 Wireless Module
Features :
- It’s easy to use and completely encapsulated.
- You can set it as a slave or master.
- You can use the AT command set the baud rate.
- Coverage up to 60 meters.
- Built-in PCB antenna.
- UART design.
- Support bridge direct-driven mode simultaneously (no need for extra CPU).
- 20ms connection interval (default), quick to connect; Support AT instruction, to modify the baud rate of the serial port, gain MAC address and modify module name.
- Support AT instruction, to adjust the Bluetooth connection interval and control the forwarding rate (dynamic power consumption adjustment).
- Support APP; IO expansion.
- 2 channel ADC input (14 bit).
- 4 channel PWM (120Hz) output.
- The RSSI successive acquisition, auto read, and notification to APP (used in anti-lost alarm).
- Power indicator/alert.
- Support anti-hijack password setup, modification, and restoration.
- Ultra-low power consumption standby mode.
₹375.00 (excl. GST)HM-10 BLE Bluetooth 4.0 CC2541 Wireless Module
₹375.00 (excl. GST) -
Hooter Security Alarm for Bank Loud Sound – 220v -110 DB
- Sound level:110 dB 100-300 Meter Distance
- Product: Electronic Siren; Frequency:800Hz to 1200 Hz
- 6 Months warranty against manufacturing defects
- Easy installation
₹550.00 (excl. GST)Hooter Security Alarm for Bank Loud Sound – 220v -110 DB
₹550.00 (excl. GST) -
HT12D and HT12E Encoder Decoder IC
Feature:
- Operating voltage: 2. 4V~12v
- Easy interface with an rf or an infrared transmission medium
- Minimal external components
- 18 Pin IC
₹75.00 (excl. GST)HT12D and HT12E Encoder Decoder IC
₹75.00 (excl. GST) -
Human Induction Fan Model Kit
The body sensing fan, in short, automatically turns on the fan when the body sensing module senses someone. When a person leaves the human body sensing module, the fan will automatically turn off, which is very intelligent.
₹500.00 (excl. GST)Human Induction Fan Model Kit
₹500.00 (excl. GST) -
HX711 Dual-Channel 24 Bit Precision A/D weight Pressure Sensor
HX711
Specifications and Features :
- Recommended excitation voltage: 5-10V.
- Two selectable differential input channels.
- On-chip active low noise PGA with a selectable gain of 32, 64 and 128.
- On-chip power supply regulator for load-cell and ADC analogue power supply.
- Selectable 10SPS or 80SPS output data rate.
- On-chip oscillator requiring no external component with optional external crystal.
- On-chip power-on-reset.
- Simple digital control and serial interface: pin-driven controls, no programming needed.
- Simultaneous 50 and 60Hz supply rejection.
₹31.00 (excl. GST)HX711 Dual-Channel 24 Bit Precision A/D weight Pressure Sensor
₹31.00 (excl. GST) -
HX711 Dual-Channel 24 Bit Precision A/D weight Pressure Sensor
- Output Sensitivity: 1.0 ± 0.1 mV / V.
- Two selectable differential input channels.
- On-chip active low noise PGA with the selectable gain of 32, 64 and 128.
- On-chip oscillator requiring no external component with optional external crystal.
- On-chip power-on-reset.
- Measurement Resolution:Â 24 bit.
₹43.00 (excl. GST)HX711 Dual-Channel 24 Bit Precision A/D weight Pressure Sensor
₹43.00 (excl. GST)
