-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)
-
Buzzer Module Board-3.3 to 5V
- Operating voltage: 3.3V-5V
- PCB Dimension: 3.1cm*1.3cm.
- Color: Blue
- Easy to use
₹30.00 (excl. GST)Buzzer Module Board-3.3 to 5V
₹30.00 (excl. GST) -
CA3130EZ CMOS Op-Amp IC DIP-8 Package
Features
- MOSFET Input Stage Provides: – Very High ZI = 1.5 T (1.5 x 1012) (Typ) – Very Low II 5pA (Typ) at 15V Operation = 2pA (Typ) at 5V Operation
- Ideal for Single-Supply Applications
- Common-Mode Input-Voltage Range Includes Negative Supply Rail; Input Terminals can be Swung 0.5V Below Negative Supply Rail
- CMOS Output Stage Permits Signal Swing to Either (or both) Supply Rails
- Pb-Free Plus Anneal Available (RoHS Compliant)
Applications
- Frequency Generator/Distorter
- Mobile jammers
- Voltage follower circuits
- DAC circuits
- Peak Signal/Noise detectors
- Oscillator circuits
Physical Attributes
- Length * Width * Height (mm): 9 x 7 x 7
- Weight (gm) : 0.2
₹35.00 (excl. GST)CA3130EZ CMOS Op-Amp IC DIP-8 Package
₹35.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Capacitive Soil Sensor V2.0 Wholesale/B2B (Pack of 25)
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹750.00 (excl. GST)Capacitive Soil Sensor V2.0 Wholesale/B2B (Pack of 25)
₹750.00 (excl. GST) -
Castor wheel with steel ball
- Dimensions: 22 x 15 mm (Diameter x Height)
- Weight: 10 gm
- Body Case Material: Plastic
- Ball Material: 304 Stainless Steel
- Application:Â for MiniQ robot
₹20.00 (excl. GST)Castor wheel with steel ball
₹20.00 (excl. GST) -
₹160.00 (excl. GST)Ceramic Capacitor Kit -300pcs (30 Kinds )
₹160.00 (excl. GST) -
Ceramic Capacitor Kit 250pcs 25 value 1PF-0.1UF
- Good Quality item
- 25 values with 10pcs for each value
₹110.00 (excl. GST)Ceramic Capacitor Kit 250pcs 25 value 1PF-0.1UF
₹110.00 (excl. GST) -
Ceramic Capacitor-220pF 1206 (Surface Mount Multilayer )- (Pack of 30)
Ceramic Capacitor-220pF 1206
- Capacitance: 220 pF
- Voltage: 50V
- Mounting type: SMD/SMT
- Operating temperature: -55ºC to 125ºC
- Supplied in tape on reel
- Nickel-barrier end termination
- RoHS compliant
- Halogen Free compliant
₹29.00 (excl. GST)Ceramic Capacitor-220pF 1206 (Surface Mount Multilayer )- (Pack of 30)
₹29.00 (excl. GST) -
Ceramic Cement Power Resistors 5W Watt 10K Ohm 5% (Pack of 5)
- Product Name : Cement Resistor;
- Body Material : Ceramic, Cement
- Power : 5W;Resistance : 10KÃŽ
- Tolerance : ±5% (J);
- Body Size (Approx.) : 22 x 9 x 10mm/0.86″ x 0.35″ x 0.39″ (L * W * H)
- Lead Diameter (Approx.) : 0.8mm / 0.031″;Color : White
₹30.00 (excl. GST)Ceramic Cement Power Resistors 5W Watt 10K Ohm 5% (Pack of 5)
₹30.00 (excl. GST) -
Charger Board Protection Module for Lithium Battery 3S 10A 12V 18650
Charger Board Protection
Features :
- Operating current : 6 – 8A.
- Current limit : 10 – 13A.
- Storage condition : -40 ~ +80 ℃.
- Resting current: less than 30uA.
- Effective lifetime: over 30,000 hours.
- Internal resistance: less than 100mΩ.
- Short-circuit protection: protection.
- Self-recovery delay.
₹46.00 (excl. GST)Charger Board Protection Module for Lithium Battery 3S 10A 12V 18650
₹46.00 (excl. GST) -
CN3791 12V MPPT Solar Charger Module
CN3791 12V MPPT Solar Charger Module
Features:
- Maximum Power Point Tracking (MPPT) Solar Charger Module
- 2-Pin JST Connectors for Solar Panel and Battery Connection
- PWM Switching Frequency of 300KHz
- Maximum Charging Current of 2A
₹195.00 (excl. GST)CN3791 12V MPPT Solar Charger Module
₹195.00 (excl. GST) -
CNC shield V3 for Engraving Machine 3D Printer A4988 DRV8825 driver expansion board
Features :
- Coolant enable
- Uses removable Pololu A4988 compatible stepper drivers. (A4988, DRV8825 and others) (Not Included)
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
- Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
- Please note that this is an unassembled kit and needs soldering.
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- PWM Spindle and direction pins
- 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
₹116.00 (excl. GST)
