-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)
-
Capacitive Soil Sensor V2.0 Wholesale/B2B (Pack of 25)
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹750.00 (excl. GST)Capacitive Soil Sensor V2.0 Wholesale/B2B (Pack of 25)
₹750.00 (excl. GST) -
5MP Raspberry Pi 3/4 Model B Camera Module Rev 1.3 with Cable
- Resolution: 5 MP
- Interface Type: CSI(Camera Serial Interface)
- Dimensions: 25x23x8 (Lx W x H) mm
- Supported Video Formats: 1080p @ 30fps, 720p @ 60fps and 640x480p 60/90 video
- Fully Compatible with Raspberry Pi 3 and 4 Model B
- Plug-n-Play camera for Raspberry Pi 3 and 4 Model B.
₹750.00 (excl. GST)5MP Raspberry Pi 3/4 Model B Camera Module Rev 1.3 with Cable
₹750.00 (excl. GST) -
Turbidity Sensor with Module
Features :
- Compatible with Arduino, Raspberry Pi, AVR, PIC, etc.
- Measures turbidity of water in rivers.
- Detects and verifies water quality.
- Digital and analog output;
- Â Able to detect particles that are suspended in water.
- Â Trimpot for sensitivity adjustment.
- Â Ideal monitoring of water turbidity in rivers, streams, lakes, water boxes, catchment and research sites, laboratories, tanks with liquids and etc.
- Comes with a module and jumpers
₹730.00 (excl. GST)Turbidity Sensor with Module
₹730.00 (excl. GST) -
Cytron 3Amp 4V-16V Dual Channel DC Motor Driver MDD3A
- Bidirectional control for two brushed DC motor.
- Control one unipolar/bipolar stepper motor.
- Operating Voltage: DC 4V to 16V
- Maximum Motor Current: 3A continuous, 5A peak
- Buck-boost regulator to produce 5V output (200mA max).
- Buttons for quick testing.
₹718.00 (excl. GST)Cytron 3Amp 4V-16V Dual Channel DC Motor Driver MDD3A
₹718.00 (excl. GST) -
Optical Liquid Level Sensor
Features:Â
- Measuring accuracy: 1MM
- Current output :15mA
- Operating voltage: 5v
- No mechanical moving parts, high reliability
- High precision level control
- Meet the safety standard requirements
- An easily mounting method with locking nut.
- Measurement range: single-point measurements
- Equipped with 50 cm cable length.
₹710.00 (excl. GST)Optical Liquid Level Sensor
₹710.00 (excl. GST) -
Stanley Allen Key Set
- Material: Metal
- Package Contains Hex Key Size: 1.5mm, 2mm, 2.5mm, 3mm ,4mm, 5mm, 6mm, 8mm ball tips
- Made using chrome vanadium steel so will resist corrosion
- Anti-corrosion treatment
₹710.00 (excl. GST)Stanley Allen Key Set
₹710.00 (excl. GST) -
Multi Purpose Display PEG Board
It is spaced from wall with molded ribs for added strength with attractive finished sides…no spacers or furring needed like other boards.
₹700.00 (excl. GST)Multi Purpose Display PEG Board
₹700.00 (excl. GST) -
Steel Frame Hacksaw -15-166 305mm/12”
- Depth of Throat: 220mm/8” 3/4”.Blade Size: 254mm / 12-Inch
- Structurally designed for maximum strength and durability
- Designed to cut metal and plastic in hard to reach places
- Ergonomically designed grip with thumb rest for maximum comfort
- Back blade stop for safe handling and use
₹700.00 (excl. GST)Steel Frame Hacksaw -15-166 305mm/12”
₹700.00 (excl. GST) -
Digital Multimeter Mastech MAS830 Series
Can Measure 200m VDC – 600 VDC
Can measure 200 VAC – 600 VAC
Can measure Resistance from 200 ohm – 2M ohm
Can measure DC current from 200 UA – 10 A
Has HOLD button through which you can hold on LCD displays the current measurement value, press thus button again to exit data hold display function₹700.00 (excl. GST)Digital Multimeter Mastech MAS830 Series
₹700.00 (excl. GST) -
Mechanical Arm DIY Kit
Mechanical Arm DIY Kit
Specification:
- Material: Wood
- Affordable 4-DOF manipulators.
- Highly versatile mechanical parts.
- Wood board laser cutting with precision.
- Easy to assemble.
₹690.00 (excl. GST)Mechanical Arm DIY Kit
₹690.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Liquid pH Value Detection Sensor for Arduino
  pH Value Detection
- Heating voltage: 5±0.2V
- Working current: 5-10mA
- The detection concentration range: PH0-14
- The detection range of temperature: 0-60 centigrade
- The response time: ≤ 5S
- Stability time: ≤ 60S
- Power consumption: ≤ 0.5W
₹680.00 (excl. GST)Liquid pH Value Detection Sensor for Arduino
₹680.00 (excl. GST)