-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)
-
Bms 13S 40A 48V Waterproof Protection Circuit Module
- 13S 48V BMS
- Discharging current – 40A
- Charging current – 20 A
- Waterproof.
₹1,250.00 (excl. GST)Bms 13S 40A 48V Waterproof Protection Circuit Module
₹1,250.00 (excl. GST) -
BMS 24V 7S 20A Daly Waterproof BMS for Li-ion Cell (NMC) 25.9V
Features :
- Strong load ability, constant discharge current 10A~250A , use high voltage resistance, low inner resistance power Mosfet. The heat sink will greatly help cooling.
- IC itself has power balancing function. The circuit is simple and reliable.
- Typical voltage detection for each cell. So each battery will be prevented over charged or over discharged. Over current and short circuit protection function is very reliable. long time short circuit of the load won’t affect the PCB and the battery. Temperature protection during charging and discharging.
- Extreme low power consumption. the consumption of the whole device is less than 50uA.
- PCB use high anti-corrosion, high water resistance, high impedance ESD conformal coating.
₹850.00 (excl. GST)BMS 24V 7S 20A Daly Waterproof BMS for Li-ion Cell (NMC) 25.9V
₹850.00 (excl. GST) -
Cretile Pioneer Kit – (45 Cretiles & Accessories)
Kit Contains 45 Cretiles and accessories:
- ProLogic: Arduino* based Programmable Cretile
- Battery/Power – 1
- Battery/Power – 2
- Push Button – 1
- Push Button – 2
- Switch
- Buzzer
- NOT Gate
- Dimmer
- Motion Sensor
- Light Sensor
- Light
- Motor – 1
- Motor – 2
- Copy
- Delay/pulse
- Receiver
- Transmitter
- U-Right
- Wire Module
- Submersible Water Pump
- Limit Switch
- Connectivity Sensor
- AND
- OR
- Toggle
- Servo Motor
- Servo Motor Driver
- High Speed Motor
- Sensor Base – 1
- Sensor Base – 2
- Obstacle Avoiding Sensor – 1
- Obstacle avoiding sensor – 2
- Sound Sensor
- Robotic Wheel – 1
- Robotic Wheel – 2
- Small wheel
- Pulley
- Pipe for Pump
- USB Rechargeable Battery 9V (500mah)
- Battery 9V – 1 (non-rechargeable)
- Battery 9V – 2 (non-rechargeable)
- OTG Adapter
- Fan Blade
- USB Cable
₹16,365.00 (excl. GST)Cretile Pioneer Kit – (45 Cretiles & Accessories)
₹16,365.00 (excl. GST) -
Cretile Explorer Kit: (22 Cretiles and Accessories with Rechargeable Battery)
Kit contains 22 Cretiles and Accessories:
- Motor with Speed & Direction control- 1
- Motor with Speed & Direction control- 2
- Light
- Buzzer
- Light Sensor
- Obstacle Sensor – 1
- Obstacle Sensor – 2
- NOT Gate
- Copy
- Dimmer
- Switch
- Battery Supply
- High Speed DC Motor
- Sensor Base – 1
- Sensor Base – 2
- Submersible Water Pump
- Plastic Fan Blade
- Robotic Wheel – 1
- Robotic Wheel – 2
- Pipe for pump
- Small Wheel
- A USB rechargeable 9V battery
Your projects can now move, make sound, sense environment, emit light & take decisions!
₹6,038.00 (excl. GST)Cretile Explorer Kit: (22 Cretiles and Accessories with Rechargeable Battery)
₹6,038.00 (excl. GST) -
Cretile Voyager Kit – (37 Cretiles and Accessories)
Set of 37 Cretile circuit modules:
- Battery/Power Supply – 1
- Battery/Power Supply – 2
- Geared Motor – 1
- Geared Motor – 2
- High Speed Motor
- Obstacle Sensor – 1
- Obstacle Sensor – 2
- Switch
- Buzzer
- Inverter – NOT Gate
- Dimmer
- Light Sensor
- Light
- Copy
- Submersible Water Pump
- Sensor Base – 1
- Sensor Base – 2
- Transmitter
- Receiver
- Pulse/Delay (Timing functionality)
- Pump/Motor
- Push Button – 1
- Push Button – 2
- Sound Sensor
- Motion Sensor
- Connectivity Sensor
- Limit Switch (approach sensor)
- Wire
- U-Right
- Robotic Wheel – 1
- Robotic Wheel – 2
- Pipe for pump
- Small Wheel
- USB Rechargeable 9V Battery
- Non-rechargeable 9V battery
- Pulley
- Fan Blade
These Cretile blocks can be used to create various projects. Your creativity will define what you can create out of it.
₹9,838.00 (excl. GST)Cretile Voyager Kit – (37 Cretiles and Accessories)
₹9,838.00 (excl. GST) -
Otto Wheel Based Robot Kit for Robotics Learning
- Part Reference: Otto DIY Bot Wheel Based
- Application: For Robotics Learning
- Color: Varies and not constant as per image
- Structure Type: 3D Printed
- Microcontroller: Arduino Nano V3
₹1,250.00 (excl. GST)Otto Wheel Based Robot Kit for Robotics Learning
₹1,250.00 (excl. GST) -
Otto Humanoid Robot Kit For Robotics Learning
- Part Reference: Otto DIY Bot
- Application: For Robotics Learning
- Color: Varies and not constant as per image
- Structure Type: 3D Printed
₹1,350.00 (excl. GST)Otto Humanoid Robot Kit For Robotics Learning
₹1,350.00 (excl. GST) -
IoT & AI Kit
- Main Controller Board: 1
- LED Matrix Module: 2
- Servo Motor: 6
- DC Motor: 4
- Push Button Switch Module: 2
- Temperature Sensor: 1
- Microcontroller Board: 1
- Vibration Sensor: 1
- Potentiometer Module: 2
- Ultrasonic Sensor: 1
- Water Level Sensor: 1
- Sound Sensor: 1
- Limit Switch Module: 2
- Soil Moisture Sensor: 1
- Buzzer Module: 1
- Colour Sensor: 1
- TFT Display (On Board): 1
- Push to Lock Switch Module: 2
- Radar (Motion) Sensor: 1
- Stepper Motor: 2
- Light Sensor: 1
- Magnetic Sensor: 1
- Moisture Sensor: 1
- Seven Segment Display: 1
- IR Sensor: 2
- Fan Module: 1
- LED Module: 2
- Servo Motor: 6
₹17,796.00 (excl. GST)IoT & AI Kit
₹17,796.00 (excl. GST) -
Robotics & AI Kit
Robotics & AI Kit
- Expansion Board – 1
- Microcontroller Board/ Microprocessor Board – 1
- Ultrasonic Sensor – 2
- Potentiometer Module – 4
- Light Sensor – 4
- Servo Motor – 6
- Magnetic Sensor – 1
- LED Module – 4
- Flame Sensor – 1
- Push To Lock Switch Module – 4
- IR Sensor – 1
- DC Motor – 4
- Microcontroller Board/ Microprocessor Board – 1
- Soil Moisture Sensor – 1
- Push Button Switch Module – 4
- Seven Segment Display – 1
- Temperature Sensor – 1
- Buzzer Module – 1
₹11,823.00 (excl. GST)Robotics & AI Kit
₹11,823.00 (excl. GST) -
Basic Robotics kit
Basic Robotics kit
ï‚·Â Breadboard – 1
ï‚·Â DC Motor – 1
ï‚·Â Buzzer – 1
ï‚·Â Green LED – 1
ï‚·Â Red LEDs – 2
ï‚·Â Push Button Switches – 3
ï‚·Â Slide Switch – 1
ï‚·Â Red Alligator Clip – 1
ï‚·Â Black Alligator Clip – 1
ï‚·Â Connecting Towers – 6
ï‚·Â 10kΩ Resistor – 1
ï‚·Â 20kΩ Resistor – 1
ï‚·Â 3.3kΩ Resistor – 1
ï‚·Â Capacitor – 1
 Jumper Wires – 3
₹10,170.00 (excl. GST)Basic Robotics kit
₹10,170.00 (excl. GST) -
Mini SD Card MP3 Sound Module For PIC Arduino WTV020-SD
Mini SD Card MP3
Specifications and Features :
- Supports FAT file system SD carrier
- Supports playing of 4Bit ADCPM format files
- Recognize the voice files automatically
- Support microprocessor and key control
- Audio output: 16bitDAC and PWM
- Maximum voice storage: 512 voice
- Operating voltage: DC 2.6 to 3.6V
- Quiescent current: 16 μA (SD card is not inserted)
₹145.00 (excl. GST)Mini SD Card MP3 Sound Module For PIC Arduino WTV020-SD
₹145.00 (excl. GST) -
ADC0809CCN-IC ADC 8BIT SAR 28DIP
ADC0809CCN
Reference Type :External
Voltage – Supply, Analog : 4.5V ~ 6.5V
Voltage – Supply, Digital : 4.5V ~ 6.5V
Features
-Operating Temperature : -40°C ~ 85°C
Package / Case : 28-DIP (0.600″, 15.24mm)
Supplier Device Package : 28-DIP
Mounting Type : Through Hole
₹75.00 (excl. GST)ADC0809CCN-IC ADC 8BIT SAR 28DIP
₹75.00 (excl. GST)
